RGB LED Diffused – 5mm / 3mm, Common Cathode or Common Anode (Single Piece)
Open this project in the Soldr app → What is Soldr.ai → wiring, code and test steps for exactly these parts
RGB LED (Diffused) – Single Piece
A single 4-lead RGB LED with a diffused (frosted) lens, so the red, green and blue chips blend into one even colour. Choose 5mm or 3mm, and common cathode or common anode to match your circuit. The longest lead is the common pin. Price is per piece and includes GST.
Key Specifications
| Specification | Value |
|---|---|
| Package | 5mm or 3mm round, through-hole, 4 leads (choose a variant) |
| Lens | Diffused (frosted) |
| Common pin | Common cathode (−) or common anode (+) (choose a variant); always the longest lead |
| Forward voltage – red (typical) | 2.0–2.2 V at 20 mA |
| Forward voltage – green (typical) | 3.0–3.4 V at 20 mA |
| Forward voltage – blue (typical) | 3.0–3.4 V at 20 mA |
| Wavelength (typical) | Red about 625 nm, green about 520 nm, blue about 467 nm |
| Current per colour (typical) | 20 mA maximum per chip; 10–15 mA recommended |
Electrical figures are typical values from common RGB LED datasheets, not a datasheet for one specific batch.
Pinout
Hold the LED with the leads pointing down and the longest lead second from the left. Reading left to right, the standard order is:
| Lead | Common cathode (CC) variant | Common anode (CA) variant |
|---|---|---|
| 1 (left) | Red anode (+) | Red cathode (−) |
| 2 (longest) | Common cathode (−) → GND | Common anode (+) → 5 V or 3.3 V |
| 3 | Green anode (+) | Green cathode (−) |
| 4 (right) | Blue anode (+) | Blue cathode (−) |
Usage Note: Which Resistor?
Use a separate resistor on each colour lead, never one shared resistor on the common lead. From 5 V: 220 Ω on red and 150 Ω on green and blue (or 220 Ω on all three for a simple, slightly dimmer setup). From 3.3 V: 100 Ω on red; green and blue need about 3.0–3.4 V themselves, so at 3.3 V they are dim and white mixing is weak; for full colour, run the LED from 5 V.
Common cathode: longest lead to GND; drive each colour pin HIGH (through its resistor) to light it. Common anode: longest lead to the supply; drive each colour pin LOW to light it, so PWM values are inverted (analogWrite 0 = full brightness, 255 = off).
What You Can Build With This
- Colour-mixing and PWM fading projects on Arduino, ESP32 or Pico.
- Multi-state status indicators (for example green OK, amber warning, red fault).
- Mood lamps and night lights.
Which type should I pick?
Most Arduino tutorials use common cathode. Pick common anode only if your code or driver circuit expects it.
Ask Soldr above what you can build with this — it knows every Compoden kit this part appears in.
Shipping Information
- Prepaid Orders: ₹45 for orders up to ₹1,999, FREE shipping above ₹1,999
- COD Orders: ₹45 shipping for orders up to ₹1,999, FREE shipping above ₹1,999. COD available.
- Delivery Timeline: Dispatch in 3-7 days, delivery in 2-7 days depending on location
Returns & Warranty
- 7-Day Return: Manufacturing defects only (approval required)
- Warranty: 7 days from delivery
- Non-Returnable: Batteries, consumables, cut wires, clearance items